Alphacam 2017 R2 Upgrade To Microsoft
Alphacam 2017 R2 License Profiles Allow
Alphacam 2017 R2 License Must Be

Vero Software Limited 9 of 43 10: What s New Machining Cylindrical Parallel - Specify Width of Cut as a Distance The option to set the width of cut as a distance has been added.

Alphacam 2016 R2 was the final release that can be installed on a 32-bit operating system.

Please refer to the Installation Guide or System Requirements page on for further information.

Alphacam 2017 R2 License Must Be

Alphacam Maintenance Expiry Date To run Alphacam, the maintenance expiry date in your license must be October 2016 or later.

Alphacam 2017 R2 Upgrade To Microsoft

Visual Basic 7.0 With the introduction of the 64-bit version of Alphacam, it was necessary to upgrade to Microsoft Visual Basic for Applications 7.0 (VBA 7).

VBA 7 is now used in the 32-bit and 64-bit Alphacam and AlphaEdit applications.

If you develop your own Add-ins and want them to work with 64-bit Alphacam, they may need to be updated.

Installation Installing Alphacam When installing Alphacam, you have the option to install either the 32-bit or the 64-bit version.

Both versions require a 64-bit operating system to enable installation.

The benefits of 64-bit Alphacam are listed in this document but it is recommended that you read the information about macros when deciding which version to install.

The APM and CDM modules are only available in the 32-bit version of Alphacam.

Importing Ribbon bars from a previous release (2016 R2) Alphacam will automatically use an existing Ribbon configuration created in a 2016 R2 installation.

When importing or exporting Ribbon configurations, the default folder location is now: LICOMDIRConfigurations.

Alphacam 2017 R2 License Profiles Allow

Vero Software Limited 5 of 43 6: What s New Licensing CLS Network Licensing Profiles Network License Profiles allow you to save your selection of system and module licenses as a single profile making it quick and easy for you to select pre-defined license options: All network licensing users can create their own set of License Profiles, and you can also copy them to a shared folder on a nominated network PC ensuring that all users can access the same ones.

You can specify a particular profile to use when you are configuring your Profiles or check the option to select one from the list that is displayed when you run the licensed application.

License Profiles are enabled and configured on the Configure Network Licenses dialog.

License Manager Dialog The Configure Network Licenses button has been added to the License Manager dialog.

Vero Software Limited 6 of 43 General Home Settings Configure srcdocs-images98137036717images7-0.jpg 7: What s New User Interface Configure Settings Dialogs - Re-styled Navigation The following configure settings dialogs have been re-styled: Home Settings Configure General Home Settings Configure Folders The tabs are now organised into a vertical list in a separate pane.

This makes it easier to navigate to the required tab and the dialogs appear less cluttered.

This displays a window with a grid containing details of the work planes in the active drawing, including the name and offset number.

Project Manager - Rename Move ClampFixture Operation It is now possible to rename the move clampfixture operation in the Quick Edit window.

Note: The new name will be displayed in the tree in the Operations Project Manager page and NC output.

Vero Software Limited 8 of 43 9: What s New Drawing Notes New Option Open with Drawing if note exists New Option Open with Drawing if note exists When enabled, this Add-ins Dialog will only be displayed if the opened drawing file already contains some Notes.

Note: This is an optional free Add-in that can be switched onoff from the Add-Ins List.

Area Estimate - Nested sheet - Include Drilled holes in scrap calculation Area Estimate of Nested sheets now takes drill Holes into account when calculating the percentage scrap area.

Alphacam 2017 R2 Download Free